Key Programming Procedure
High config vehicles with PSPS:
Add key when working key is available, vehicle is not in alarm state:
JPLA ver: Replace RFA—> Modify vehicle config—> Copy and add smart key.
K8D2 ver: Replace RFA—> Modify vehicle config—> Copy and add smart key, or modify vehicle config—> copy and add smart key—> Replace RFA.
On AKL condition, vehicle is in alarm state:
Connect JLR cable well(refer to 'Attention'), then enter [All smart key lost] function menu, use Lonsdor JLR key to generate an emergency key, after generation press the remote's unlock button to disarm vehicle alarm state. After disarming the state, unplug the JLR cable. No need to connect JLR cable while replacing RFA and modifying vehicle config.
JPLA ver: Replace RFA—> Modify vehicle config—> Copy and add smart key.
K8D2 ver: Replace RFA—> Modify vehicle config—> Copy and add smart key, or modify vehicle config—> copy and add smart key—> Replace RFA.
Low config vehicles without PEPS:
Add key when working key is available, vehicle is not in alarm state:
Enter [Copy and add smart key] function menu, use Lonsdor JLR key to add new key.
For some models, the system will notify that adding key is not supported currently as 32-bit SK is required, follow AKL programming operations may have the risk that working key programming fails.
On AKL condition, vehicle is in alarm state:
Connect JLR cable well(refer to 'Attention'), then enter [All smart key lost] function menu, use Lonsdor JLR key to add new key.
Read vehicle info
Communicating...
Vehicle info:
(1) VIN code: L2CCXXXXXXXX02462
(2) Vehicle type: L550
(3) RFA part number: K8D2-14C250-BA
(4) RFA software version: K8D2-14C104-AF
(5) RFA calibration data number: LK72-14C105-CA
(6) RFA network signal calibration number: K8D2-14C430-AB
(7) RFA locked or not: No
(8) Remote frequency: 434MHz
(9) UWB function enabled or not: No
Copy and add smart key
This function can copy and add key in the position of working key, and generate new key in the position of lost key, please note:
(1) For low config models without PEPS, the generated key function is complete, can be used directly. For high config models with PEPS, the key has RKE and Emergency Start functions ONLY (no PKE) after copy finished;
(2) RKE function of the copied key will conflict with the working key in the same key position;
(3) New key to be generated must be Lonsdor dedicated JLR(2018+) key.
Communicating...
Software ver: K8D2-14C104-AC;
Pls prepare all working keys, and in turn to place each key into this device's card slot to idenitify. Pls note: if a working key is not identified in the slot, after new key generation completed, RKE function of the unidentified working key will become invalid;
Pls place the working key to be identified into this device's card slot;
Reading and writing key...pls keep the key placed stably;
Identified key info: key ID: 59B6F4E7 , remote sync code: 1FFB4E00;
Pls select the position with key ID to copy and generate working key;
Pls place the key to be generated into this device's card slot;
Reading and writing key...pls keep the key placed stably;
Key generation success, if current vehicle is in alarm state, pls press the remote's unlock button to disarm the state;
Program completed.
All smart key lost
This function is for AKL condition, please note the following points, use it with caution:
(1) It will delete all working keys and doesn't support the lost keys to be re-programmed to the vehicle;
(2) New keys must be Lonsdor dedicated JLR(2018+) key;
(3) For low config models, it supports AKL programming (generate key directly). For high config models, require to use car dealer tool to execute [Replace RFA] process first, and then modify car config (namely, disable UWB function), before using this function to do AKL;
(4) High config models use this function directly when no config data modified, and the generated key has RKE and Emergency Start functions ONLY (has no PKE).
Communicating...
Software ver: K8D2-14C104-AC;
Pls select the position with key ID to copy and generate working key;
Pls place the key to be generated into this device's card slot;
Reading and writing key...pls keep the key placed stably;
Key generation success, if current vehicle is in alarm state, pls press the remote's unlock button to disarm the state;
Program completed.
Identify smart key
Pls place the smart key to be identified into this device's card slot;
Reading and writing key...pls keep the key placed stably;
Key ID: 59B6F4E7.
Modify vehicle config
This function is designated for JLR(2018+) high config models, by using it to disable UWB PEPS function, support for low equipped keys to be programmed to the high config models.
(1) Backup vehicle config data: back up config data of current vehicle;
(2) Modify vehicle config data: disable UWB PEPS function;
(3) Restore vehicle config data: restore the config data backed up before to current vehicle.
Back up vehicle config data;
Communicating...
Pls enter the filename;
Backup success;
Modify vehicle config data;
Communicating...
Reading data...
Disable/turn off UWB PEPS function;
Configuring system...
Completed.
Replace RFA
This function is the programming process of replacing RFA module for JLR(2018+) models, pls note the following:
(1) If current vehicle RFA is locked, [Replace RFA] process cannot be executed;
(2) Confirm that current vehicle has installed brand new RFA module, or that the main chip of current RFA has been replaced with a brand new chip SPC560B60L3 and initial data has been written;
(3) Vehicle battery voltage should be kept above 12V, otherwise exception may occur during programming, highly suggest that you plug external 12V DC to power up vehicle battery.
(4) Pls prepare at least two keys which can be programmed to current vehicle.
(5) In vehicle alarm state, pls disarm the alarm first before function execution.
Communicating...
Read info:
Part no.: JPLA-14C430-AB
Software ver: JPLA-14C104-AE
VIN code: SALGA2BV4JA******
The program will turn ignition on automatically, pls confirm the ignition is turned off;
The following process is to execute RFA data programming function, if current RFA has been executed once a complete data programming, can skip over this process. Click OK to execute RFA data programming; click Cancel to enter key programming process directly.
Loading...
Erasing data storage block...
RFA data programming completed, to program key multiple times, can skip over this process, and directly enter key programming function.
Configuring system...
The program will turn ignition on automatically, pls confirm the ignition is turned off;
Learning VIN...
Writing immo ID...
Pls prepare at least 2 keys to be programmed, and place the key inside the vehicle, need to press the unlock button during programming, click OK and follow the prompts, start to program key;
Pls hold the smart key to be programmed in hand;
Press hard and hold the unlock button for 4s, the buzzer beeps twice to indicate current key programming success;
Program completed.
Write RFA initialized data
Pls select RFA module No.:
(1) JPLA-XXXXXX-XX
(2) K8D2-XXXXXX-XX
(3) J9C3-XXXXXX-XX
Writing DFLASH data...
Writing CFLASH data...
Success.
Modify remote sync code
This function is only used for JLR(2018+) low config models when the key has smart and emergency start function, but doesn't have remote function after key copy & add is complete. You're required to try to modify remote sync code, then test if the remote function works properly. The smart key must be an unlocked one.
Two ways to modify remote sync code:
(1) Enter value, manually enter remote sync code to modify;
(2) Tap button, choose to increase by 10000000 or 100000 to modify.
Generally, the sync code of copied key is fixed to be 80808000, try to modify the first number (e.g. 90000000, A0000000, B0000000, C0000000, D0000000, E0000000, F0000000, 00000000, 10000000, 20000000, ..., 70000000), if these value don't work, then try 00100000, 00200000, 00300000, ..., 00F00000, don't forget to test remote function after each modification until it works properly. If none of the modified value are correct, you have to replace RFA's CPU.